The L dimension is equal to the pipe inside diameter. Failure to follow these instructions carefully may cause … 7. Once all the studs are inserted and hand-tightened, the studs must be torqued to 80 ft-lb N-m in three stages. Set the torque wrench to 30 ft-lb 40 N-m and torque the studs in the order shown below. Set the torque wrench to 60 ft-lb 81 N-m and torque in the order shown below.
Set the torque wrench to 80 ft-lb N-m and tighten in the order shown above. Repeat steps 1 through 4 for the other nozzle. Wrap the strip of film around the pipe with one edge running along the vertical scribe line at the first nozzle location.
Make sure the strip overlaps squarely around the pipe and mark the overlap position of the strip. This equals the circumference of the pipe. Remove the strip of film and fold it as shown below to determine the position which is diametrically opposite the overlap position when the film … Installing Pipe Nozzles Chapter 2.
Nozzles are installed in a Tilted 45 o configuration. Maintenance 4. Remove the junction box from the end of the transducer by loosening the compression fitting and unscrewing the junction box.
Compression Fitting … Chapter 2. Before welding the first boss, you must add another scribe line known as the oblique center line. The oblique center line compensates for the slope or oblique of the boss.
Using a metal edge, scribe a vertical and a horizontal line 6 in. Side View Side View … Information Chapter 1. Information 1. These transducers measure the flow rate of saturated steam and most gases through pipes having diameters between 2 in. Such measurements are independent of the pipe material. Screw the threaded rod into boss that is welded onto the pipe.
If necessary, remove the washer and nut from the threaded rod. Insert the pipe section of the jig into the … Install a new flange gasket on the pipe nozzle. Repeat steps 3 through 6 for the other transducer if necessary. You have completed the removal procedure, it is now safe to reopen the process line. Bolts Bolts Gasket Blind Flange … Sensor Cook Buttons Sensor settings to cook popular foods.
Page Installation Installation The Microwave Oven is supported by a special bracket assembly mounting system supplied with the oven. The bracket assembly must be mounted to the wall with toggle bolts through the wall, and a lag screw into a wall stud. After the bracket assembly is installed, the unit can be slid over the two rails of the bracket assembly.
Page Disassembly And Reassembly 4. Then remove the door assembly. Page Reassembly Test Reassembly Test After replacement of the defective component parts of the door, reassemble it and follow the instruc- tions below for proper installation and adjustment so as to prevent an excessive microwave leakage. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
Disconnect power and remove grille screws 2. Remove grille and the bracket duct upper screw 1. Remove the bracket duct upper and disconnect the stirrer motor wire. Remove stirrer motor screws 1 and lift up stirrer motor after turn left. Disconnect power and remove grille.
Remove a screw securing the control box assembly. Be sure to ground any static electric charge in your body and never touch the control circuit. Page Alignment And Adjustments 5. High voltage is present at the high voltage terminals during any cook cycle. It is neither necessary nor advisable to attempt measurement of the high voltage. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high voltage capacitor.
Check continuity of the capacitor with the meter set at the highest resistance scale. A shorted capacitor will show continuous continuity. The blower is operated by low voltage relays located on the smart board. They are : 1. Hood thermal cutout, inside control area on duct.
Page Hood Thermal Cutout Hood Thermal Cutout This cutout will protect the touch control from exces- sive heat by turning the vent fan on at low speed. It is designed to prevent damage to the magnetron if an overheated condition develops in the tube to cooling fan failure, obstructed air ducts, dirty or blocked air intake.
The output power of the magnetron can be measured by performing a water temperature rise test. Page Troubleshooting 6. Misadjustment or loose wiring Adjust door and latch switches. Defective primary latch switch Oven can program but timer 1. Open or loose wiring of secondary i Adjust door and interlock switches. All sensors and devices have their own number. Page Diagrams 8.
B Diagrams P. Page Parts List P. B Parts List S. Page 38 P. B Parts List continued S.
0コメント