Always place the cut end of the first plank against the wall Figure 4. STEP 10 Fitting around irregular objects, no problem. Simply make a pattern out of heavy paper to fit around pipes or irregular objects. Place the pattern upon the plank and trace.
Cut along trace lines using a utility knife or heavy duty scissors, and lay plank. Be sure to leave a minimum of 3mm expansion space around all fixed objects, floor vents and door frames. STEP 11 The beauty of allure locking is the ease of installing the opposite way. You can install from both sides of the plank. This allows you to start in one room and continue through a doorway into another room with the same pattern and continue installing the floor forwards or backwards.
If you need to replace a plank of allure locking allure flooring , simply take a utility knife and cut the bad plank out along the long side of the plank only and lift out of place. Then take a spare plank and cut the tongue and groove off of the long side of the replacement plank only. Leave the tongue and groove on the short side of the plank. This helps get the sand and grit from getting on your floors. Gritty sand is the worst enemy of any floor covering.
Install proper floor protectors felt preferred on all furniture legs used on resilient flooring. Protectors will allow chairs to move easily over the floor without scuffing and scratching. Clean protectors on a regular basis to remove any grit that may have become embedded on the bottom of the furniture leg. For any swiveled type office chairs and other rolling furniture, please install 5cm wide non staining flat casters.
Do not use rubber casters 3. To keep your floor looking its best, dust mop or vacuum your floor at least twice a week. Do it more often on floors with heavy traffic. Do not use a household dust cleaner of amy kind as this may cause the floor to become slick or damage the finish.
Simply sweep the floor as often as needed. Do not allow pets with unclipped nails to damage your allure floor. It may result in severe scratching to the surface. The same is true for any high heeled shoes that do not have proper tips on the heels. Avoid exposure to direct sunlight for prolonged periods of time.
During peak sunlight hours, use drapes or blind to minimize the direct sunlight on the allure floor. Most types of flooring will be affected by continuous strong sunlight. To avoid uneven appearance, please consider relocations of any area rugs from time to time. In addition, excessive temperatures are not good for resilient floors.
Some natural ventilation or intermittent air conditinion in vacant homes should be considered. You may remove chewing gum, adhensive, crayon, candle wax and similar type of subtances by applying ice until it becomes brittle enough to crumble off. The residue may be removed with mineral spirits 2.
Extra deep heel marks, caster marks etc: rub with green Scotch Brite pad dampened with allure Single Step3. For moderate to heavy stains caused by long standing water or other non dye liquids: Rub with allure Single Step4.
For dark spots caused by ink or other chemicals, clean spot as per 2 above. If not successful, then the effected plank should be replaced.
Animal and diaper stains should be traeted same as 3 above6. Cigaratte burns if not deep, then procedure 2 above should work. If however, they are very deep then the affected plank shold be replaced. Food spills should be cleaned up as rapidly as possible with a quality liquid vinyl cleaner. We do not recommend powdered cleaners, oil soaps, dishwashing detergents, or other dusting products.
Try to use a non rinsing, biodegradable cleaner that leaves no residue or haze and requires no rinsing after application 2. Shoe marks and scuffs can be easily removed using a spot application of your allure Single Step 3.
Regular household dirt can be cleaned with your allure. Single Step applied as indicated on products label. Some hand wiping may be required to remove tough spots and spills.
Always sweep or vacuum your allure floor before cleaning so that all loose dirt and particles are removed. The surface of your allure is very dense and non porous; this prevents wax from penetrating and thus will build up a bed for yellowing and dirt collection. The same non porous feature also provides all the protection against wear and staining all the protection against wear an dstaining that you will need.
Use only allure Single Step for heavy wear when you have experienced some loos of the original appearance over time. To install place the overlapping GripStrip of one plank onto the adjacent plank and press together.
Use the TrafficMaster Allure Tile 12 in. Know that allure is for interior installations. For use indoors and temperature controlled environments only see installation instructions for. Durable vinyl tile is textured to look like real ceramic flooring Highly water-resistant tile installs easily with GripStrip design Can be installed over concrete tile vinyl or wood Ashlar color finish offers the natural look of real ceramic tile flooring 38 mm thickness x 12 in.
Width x 36 in. Allure Gripstrip flooring is easy to install no-mess and works over most existing floors. With our patented GripStrip process you just lay the allure planks down and secure them together easily with no messy adhesive required. This high tensile system ensures no gapping and has allowed Allure to become WORLDs first vinyl plank that is installed as a floating floor.
This patented design is water-resistant lightweight yet durable and easy to install.
0コメント